COOL BOOST SYSTEMS STAGE 1 SINGLE NOZZLE WATER METHANOL INJECTION KIT
This Cool Boost Systems Stage 1 Single Nozzle Water-Methanol Injection System is designed for individuals requiring a single point for injection with fluid delivery in a fixed manner.
This system includes a Stage 1 Display allowing the driver to be informed of system activation, low pressure and low level faults during use.
This system is not suited specifically to a particular vehicle and is therefore Universal as includes a range of nozzles in various flow rates to allow for exchanging to reach optimal results on the intended platform.
This system also includes a Fluid Level and System Pressure monitoring unit for the detection and warning of low fluid levels and system pressure faults.
This Stage 1 Water-Methanol Injection Kit includes all the necessary hardware to allow for a complete system installation to your vehicle.
This system will activate based on a setpoint boost pressure which is adjustable between 0.4-1.2Bar
.
Features of the Stage 1 System:
* Set & Forget Setpoint Adjustments (setpoints cannot be altered unless saved by user)
* Manual System Priming Feature (Prime the system as long as you want - Useful for prerun cooling)
* System Test Function (System will run pump until pressure is detected and then shut off - SPMU Required)
* Controller Failure and Wiring Defect Detection (Pump And Solenoid Circuit Failure Monitoring)
* System Pre-Pressurisation Technology (Reduces injection latency and improves consistancy)
* 3 Stage Electrical Isolation (Double Pole Circuit Switching method prevents run away injection / hydrolocking)
* System Pressure Monitoring (Closed loop injection strategy provides surety of injection)
* Blocked Nozzle/s Detection (Detection of blocked nozzle/s - requires SPMU and Solenoid per nozzle)
* Configuration Menu (Activate/ Deactivate Pre-Pressurization, switch between Aux Input/ Output Modes)
* Boost Safe Output (Safety output can be utilized to prevent the vehicle from entering high boost or cut ignition)
* Fluid Level Monitoring (Monitoring of Fluid Levels with nuisence alarm prevention algorithm)Â
.
Benefits Of Water-Methanol Injection
* Increase power output safely by 15-20%
* Lower air temperatures by 10-50°C degrees
* Increases octane by up to 25 RON and only when you need it during racing
* Reduces cylinder temperatures up to 150°C degrees
* Detonation and Pre-Ignition becomes a distant memory
* No wear issues only clean combustion chambers
* Allows you to safely run more boost and timing
.
So you now know what it can do, what does it do to your vehicle's engine?
A Water-Methanol Injection Kit's main purpose is to suppress detonation caused by high temperature and pressure that has developed in the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point, by either a turbo, supercharger or high compression pistons.
Compressed air is heated air that causes a reduction of power and increases the likelihood of detonation.
Our kits help lessen any reduction of power while also increasing fuel economy by instantly cooling the compressed air in the boost pipes before the throttle body and also in the combustion chambers during ignition.
Because Water and Methanol have a very high latent heat content, it is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in modern lean burning engines.
Methanol, with its 116 octane high flash points and specific gravity, helps further reduce the chances of detonation and acts as a fuel itself in the combustion chamber.
.
The kit contents of the Stage 1 Single Nozzle Injection System
Fluid Delivery Components
1 x LeakProof Tank Outlet Fitting 90 Degree with built in strainer
2 x LeakProof Pump Fitting - Swivel 90 Degree
1 x 20Bar Water Methanol Injection IP65 Pump
6 x Meters Length of Blue 1/4" Nylon Piping
Electrical Components
1 x Stage 1 Display with 5 meter wiring harness
1 x 0.4-1.2Bar Boost Pressure Switch
1 x Reservoir Fluid Low Level Switch
1 x 1/8NPT Vacuum Barbed Fitting
1 x 4mm Vacuum T-Piece
1 x 3mm Silicone Vacuum Tube Connector
6 x General Securing Cable Ties
4 x Vacuum Pipe Securing Cable Ties
2 x Round Terminal Lugs
1 x Roll of Cloth Tape
1 x 10mm Rocker On/Off Power Switch
1 x Cool Boost Systems Lanyard
2 x Quarter Panel Window Stickers