• New
  • Pack
Cool Boost Stage I Basic Kit

COOL BOOST SYSTEMS STAGE 1 BASIC SINGLE NOZZLE WATER METHANOL INJECTION KIT

This Cool Boost Systems Stage 1 Single Nozzle Water-Methanol Injection System is designed for individuals requiring a single point for injection with fluid delivery in a fixed manner.

This system includes a Stage 1 Display allowing the driver to be informed of system activation, low pressure and low level faults during use.

This system is not suited specifically to a particular vehicle and is therefore Universal as includes a range of nozzles in various flow rates to allow for exchanging to reach optimal results on the intended platform.

This system also includes a Fluid Level and System Pressure monitoring unit for the detection and warning of low fluid levels and system pressure faults.

This Stage 1 Water-Methanol Injection Kit includes all the necessary hardware to allow for a complete system installation to your vehicle.

This system will activate based on a setpoint boost pressure which is adjustable between 0.4-1.2Bar

.

Key Features of the Cool Boost Stage 1 Basic System:

*Fluid Level Monitoring

*System Pressure Monitoring

*Leak Proof Components

*Easy to install

.

Quick Benefits Of Water-Methanol Injection

* Increase power output safely by 15-20%

* Lower air temperatures by 10-100°C degrees

* Increases octane by up to 25 RON and only when you need it

* Reduces cylinder temperatures up to 150°C degrees

* Detonation and Pre-Ignition becomes a distant memory

* No wear issues only clean combustion chambers

* Allows you to safely run more boost and timing

.

What does WMI do to your vehicle's engine?

A Water-Methanol Injection Kit's main purpose is to suppress detonation caused by high temperature and pressure that has developed in the combustion chambers when the effective compression ratio has been taken beyond the auto-ignition point, by either a turbo, supercharger or high compression pistons (N/A).

Compressed air is heated air that causes a reduction of power and increases the likelihood of detonation.

Our kits help lessen any reduction of power while also increasing fuel economy by instantly cooling the compressed air in the boost pipes before the throttle body and also in the combustion chambers during ignition.

Because Water and Methanol both have a very high latent heat of evaporation, it is extremely effective for controlling not only the onset of detonation throw suppression but also the production of oxides of nitrogen in modern lean burning engines.

Methanol, with its 116 octane high flash point and specific gravity, helps further reduce the chances of detonation and acts as a fuel itself in the combustion chambers.

.

The kit contents of the Stage 1 Basic Single Nozzle Injection System

Fluid Delivery Components

1 x LeakProof Tank Outlet Fitting Straight with built in strainer

2 x LeakProof Pump Fitting - Swivel 90 Degree

1 x 20Bar Water Methanol Pump IP65 Rated

6 x Meters Length of Blue 1/4" Nylon Piping

1 x Non Return Valve incl LeakProof Fittings

1 x LeakProof Side Feed Nozzle Holder

1 x CB3 Filtered High Atomising Nozzle

1 x CB5 Filtered High Atomising Nozzle

1 x CB7 Filtered High Atomising Nozzle

Electrical Components

1 x Stage 1 V2 Display (Indications of Activation, Low Level and Low Pressure)

1 x System Pressure Monitoring Unit

1 x Reservoir Fluid Low Level Switch

1 x Adjustable Boost Pressure Switch (0.4-1.2Bar - Preset to 0.5bar)

1 x 5m Pre-Wired Easy install Wiring Harness with relay built in

2 x Round Terminal Lugs

1 x 1/8NPT Vacuum Barbed Fitting

1 x 4mm Vacuum T-Piece

3 x Meters of 3mm Vacuum Black Nylon Piping

6 x General Securing Cable Ties

4 x Vacuum Pipe Securing Cable Ties

1 x Roll of Cloth Tape

1 x 10mm Rocker On/Off Power Switch

1 x Cool Boost Systems Lanyard

2 x Quarter Panel Window Stickers

CBS-K-S1B-1
To top

New Account Register

Already have an account?
Log in instead Or Reset password